HOME | DD

Description
ok first i cut out:
1 back body
1 frint body
2 anteni
4 arms
4 leg B
2 leg A

Remember if you are useling material that is diffrent on both sides that you need to flip the pattern piece for halfr of the pieces ... if you get me.
ok so on the body front i forgot the tabs .. so sue me

ok thre is a dart at the top of the back of tyhe head and the front belly to give them a lil shape. bacicall i sew them first and ajust so that they match up with the opostie side. remember to add a lil hem or you will end up with a too small flappy bitlater. ok.. now i do bullets

1. hem the darts in the front and back body

2. sew the arm pieces onto the front and back body

3. sew the anteni onto the front and back body

4. sew both the body pieces together. remember the outside's need to be faceing each other. start about quater of the way around the belly curve (so you have a hole to put stuffing in later) and go up. if you have pins use them so you dont end up getting ahead of yourself on one side and then the pattern pieces dont match up.

5. flip it all right way out by pulling everything out the hole you left. my anteni was too small so i had to cut off the end and sew it on seperate.

6. stuff your pupu. make sure to start off my filling the arms and anteni tight. theres nothing more frustrating than finishing and discovering you have a floppy pupu. then fill the head. make sure you cram it in tight as you go. then the neck. if there is too lil in the neck his head will flop O.o and you dont want that. then sholders, belly and then a lil extra just incase.

7. hand sew the hole. make sure you fold in the edges. i segest pinning them together first

8. pin 2 leg B pieces together along the long curved edge (rememer to put the two outside surfaces together). then put in leg A. right .. its hard explaing where it goes but here goes. looking at the pik. flit leg a the other way. now sew it to the leg be side onf the same length (left) then sew the other side to the same side but of the back leg b piece. if you lay it flat now leg A will fold inside leg B. now sew that long edge of the leg B's.

9. now flip it right way out and stuff it tight as pos

10. flip the edge in and pin a hem (this will slightly hold in the stuffing)

11. repeat 8-10 on the other 3 leg pieces

12.sew the hem'd edges where you think the legs should go and then remove the pims

13. now the actual plushy - [link]

14. Look at the eyes...Don't do this. XD

Description
ok first i cut out:
1 back body
1 frint body
2 anteni
4 arms
4 leg B
2 leg A

Remember if you are useling material that is diffrent on both sides that you need to flip the pattern piece for halfr of the pieces ... if you get me.
ok so on the body front i forgot the tabs .. so sue me

ok thre is a dart at the top of the back of tyhe head and the front belly to give them a lil shape. bacicall i sew them first and ajust so that they match up with the opostie side. remember to add a lil hem or you will end up with a too small flappy bitlater. ok.. now i do bullets

1. hem the darts in the front and back body

2. sew the arm pieces onto the front and back body

3. sew the anteni onto the front and back body

4. sew both the body pieces together. remember the outside's need to be faceing each other. start about quater of the way around the belly curve (so you have a hole to put stuffing in later) and go up. if you have pins use them so you dont end up getting ahead of yourself on one side and then the pattern pieces dont match up.

5. flip it all right way out by pulling everything out the hole you left. my anteni was too small so i had to cut off the end and sew it on seperate.

6. stuff your pupu. make sure to start off my filling the arms and anteni tight. theres nothing more frustrating than finishing and discovering you have a floppy pupu. then fill the head. make sure you cram it in tight as you go. then the neck. if there is too lil in the neck his head will flop O.o and you dont want that. then sholders, belly and then a lil extra just incase.

7. hand sew the hole. make sure you fold in the edges. i segest pinning them together first

8. pin 2 leg B pieces together along the long curved edge (rememer to put the two outside surfaces together). then put in leg A. right .. its hard explaing where it goes but here goes. looking at the pik. flit leg a the other way. now sew it to the leg be side onf the same length (left) then sew the other side to the same side but of the back leg b piece. if you lay it flat now leg A will fold inside leg B. now sew that long edge of the leg B's.

9. now flip it right way out and stuff it tight as pos

10. flip the edge in and pin a hem (this will slightly hold in the stuffing)

11. repeat 8-10 on the other 3 leg pieces

12.sew the hem'd edges where you think the legs should go and then remove the pims

13. now the actual plushy - [link]

14. Look at the eyes...Don't do this. XD